Orne Brocaar 1076

• asked Jul 3

ChirpStack v4.19.0-test.6

v4.19.0-test.6 Features Class-B improvements This release adds a class_b_schedule_advance configuration option, which controls how far in advance a Class-B downlink can be scheduled. The previous behavior was to immediately schedule the nex...

announcements

0 votes

0 answers

16 views

jerome 3

• asked Jun 26

Run Chirpstack v3 and v4 in parallel, same VM, officel .deb packages

Hi. I would like to ask again [a question I asked in the old forum] . It didn't get any answer, perhaps because it was buried in a question with a wider scope. Basically, (last time I checked) nothing in the official Debian packages pre...

configuration chirpstack chirpstack-v3

0 votes

1 answers

29 views

hiroshi shimomichi 1

• asked Jun 25

SQLite Integration Configuration

HI, When using PostgreSQL for integration, the events data can be stored in the chirpstack_integration table. Is there a similar integration configuration available for SQLite?

integrations chirpstack

0 votes

1 answers

27 views

Guy 11

• asked Jun 24

Announcing opcgw — a ChirpStack → OPC UA gateway

Hi everyone, I'd like to share opcgw, an open-source gateway I've been developing that bridges ChirpStack 4 with OPC UA, so LoRaWAN device data can flow into industrial automation systems (SCADA, MES, edge) without writing custom gl...

integrations chirpstack

1 votes

0 answers

42 views

Luca Paredi 1

• asked Jun 24

Gateway mesh stop working , error "Operation cannot be accomplished in current state"

Hello everyone, I am running several mesh networks using ChirpStack OS. Randomly, the mesh system refuses to process downlinks, and the following error appears in the logs: 'Operation cannot be accomplished in current state'. I susp...

chirpstack-gateway-mesh

0 votes

1 answers

69 views

aldo morales 1

• asked Jun 22

Use of Tektelic 64-channel gateway

Good afternoon, team. I need a little guidance on the correct use of TomL files when using 64-channel gateways. The TomL files explain that to listen to all gateway channels, I need to change this to # enabled_uplink_channels=[].. However, ...

troubleshooting chirpstack tektelic

0 votes

1 answers

61 views

Stefan Hofmann 1

• asked Jun 18

Integration Queue

I would like to ask if this feature would be something of interest for others: We use different types of Integrations (mainly MQTT, HTTP and InfluxDB). Especially for the HTTP Integration, we have sometimes the problem, that the endpoint (w...

feature-request chirpstack

0 votes

0 answers

21 views

Alejandro Von Chong 1

• asked Jun 17

Help migrating a Browan/Gemtek WAPS-232N_LW from ThingPark/Actility firmware to OPDK for ChirpStack

Hi everyone, I’m trying to figure out whether I can reuse a Browan / Gemtek Outdoor Micro Gateway with my own ChirpStack setup, but I’m a bit stuck because this unit seems to be running the Actility / ThingPark firmware instead of the gener...

gateways chirpstack browan

0 votes

0 answers

22 views

Christopher Haas 1

• asked Jun 17

Invalid Length error in gateway menu after backup/restore..

Hi, today i managed to backup and restore my chirpstack docker environment. After testing i saw an error, which i can not identify - i dont know even, if this does impact anything by the way. Tenant -> Gateways -> Overview page Error ...

troubleshooting chirpstack

0 votes

2 answers

36 views

Nick Grigoriadis 1

• asked Jun 16

Handling Fragmented Uplinks in Payload Codec

Hello, I have a device based on a RAK3172 that sends data using fragmented uplinks. My question is about the ChirpStack payload codec behavior. Is it possible for the codec to somehow keep received fragments in memory, wait until all fragme...

chirpstack codecs lorawan rak-wireless

0 votes

1 answers

22 views